Most homeowners pay $450 to $650 to replace a standard pair of garage door springs, parts and labor included. Longer-lasting springs with longer warranties cost more. AG Smart Garage replaces broken springs across most of the Chicago area, with most of our work on the North Shore, usually in the same visit, and the in-home consultation is free: you only pay if you go with us. We are one of the few garage door companies in Chicagoland that weighs every door before choosing its springs, and a family-owned company with in-house, licensed and insured technicians, based at 444 Lake Cook Road in Deerfield. Call (224) 306-2985.
If your door went up an inch and stopped this morning, or you heard a bang from the garage last night, you probably want a number before you call anyone. Fair enough. Here is what spring replacement costs in 2026, what moves the price up or down, and how to tell which spring fits your house.
The short answer
| Spring | Typical price range (parts and labor) | Built for |
|---|---|---|
| Standard (10,000 cycles) | $450 to $650 | Most households |
| High-cycle (20,000+ cycles) | $650 to $900 | Busy doors, longer warranty |
| Lifetime-type (80,000+ cycles) | $1,000 and up | People staying in the home for good |
These ranges cover a standard residential torsion system with one or two springs. Where your job lands in the range depends on your door, the springs it needs and the warranty you choose. Our technician weighs your door and gives you the exact price for each option before any work starts.
What a proper spring replacement includes

A spring replacement done right is more than swapping a coil. Here is what happens on our visit:
- We weigh your door. With the old springs unwound, the door goes on a scale. Spring size comes from the real weight, not a guess from the old spring, because the old spring may have been the wrong size to begin with. (More on why below.)
- We size the new springs to that weight with spring engineering software and match them to what is on the van, so most jobs are finished in the same visit.
- We replace both springs on a two-spring door. Springs on the same door have done the same number of cycles. When one breaks, the other is close behind. Replacing both keeps the door balanced and saves you a second visit. (More on that in our post on whether to replace one or both garage door springs.)
- We wind, set and lubricate them, then test the balance by hand with the opener disconnected. A balanced door stops and stays where you leave it.
- We run the door and test the safety features: the safety eyes and the auto-reverse.
- We do a 33-point safety inspection. If we find anything else, we show you the actual part and you decide. Nothing extra happens without your approval.
Why we weigh every door (and most companies don't)
Most spring replacements are sized by reading the old spring: same wire, same length, put it back. That only works if the old spring was right, and often it was not. Doors get heavier over the years: insulation added, a new panel, windows, paint, a few coats of ice in January. A spring that is too weak makes the opener do the lifting and wears it out; a spring that is too strong makes the door fly up and fight the opener on the way down. Either way the new spring dies early.
So we put the door on a scale, every time. We are one of the few garage door companies in Chicagoland that does this. The real weight goes into spring engineering software, which picks the wire size and length that balance your door for the cycle rating you choose. The result is a door that stays where you leave it, an opener that is not straining, and a spring that lasts as long as it is rated to.
Why springs come in different grades
A spring is rated in cycles. One cycle is the door going up and coming back down. Every spring wears out after a certain number of cycles, set by the wire thickness, the coil size and the length.
The standard spring is rated for 10,000 cycles (what spring cycles mean). How long that lasts depends on how your family uses the door:
- A couple who drives out a few times a week may never wear out a standard spring before they move.
- A typical household that runs the door four to six times a day gets roughly five to seven years.
- A busy family that uses the garage as the front door can burn through 10,000 cycles in under two years.
Our owner Adi uses his own house to explain this. Four kids, one garage door everybody uses, about 20 cycles a day. A standard spring on that door would be back on the floor in well under two years.

A higher-cycle spring uses heavier wire and more length for the same lift, so it costs more up front and lasts much longer. That is the whole reason for the price difference.
How to pick yours
Two questions settle it:
- How many times a day does the door run? Count the cars, the kids and the dog walks. If the garage is your front door, assume it is busy.
- How long are you staying in the house? If you plan to sell in the next couple of years, a standard spring is the honest pick. If you are staying for good, a lifetime-type spring is the one that pays you back.
Our technicians ask exactly these two questions before they recommend anything, and then you choose.
What can change the price
Heavy or oversized doors
Most Chicago-area homes have a standard torsion system. Very heavy doors, such as solid wood, oversized or heavily insulated doors, need bigger, thicker springs, and those are priced differently. We quote them at the door after weighing it.
Extension springs
Some older or lighter doors use extension springs, the long springs that stretch along each horizontal track instead of one bar above the door. Replacing a pair usually costs about the same as a standard torsion pair.
Converting extension springs to torsion
If you want a quieter door with longer-lasting springs, or the extension hardware itself is worn out, we can convert the door to a torsion system: the torsion tube, springs, drums, cables and bearing plates. Expect roughly $900 to $1,300 for most doors, and the new torsion springs then come in the same grades as above.
Cables
Cables lift the door together with the springs and have done the same number of cycles. We recommend new cables with every spring change, always as a pair, and we show you the old ones once the springs are off so you can see their condition yourself. Stainless cables cost a little more and rust much more slowly in a salty Chicago-area garage. If a cable has come loose while the door was open, start with our post on a garage door cable loose when the door is open.
Why a lower quote may not be the same job
You may hear a lower number on the phone. Before you compare, ask what it includes:
- Is the spring rated for at least 10,000 cycles? Low-cycle springs exist, and they wear out fast.
- Are they replacing one spring or both? A one-spring price looks cheaper today and usually means a second visit.
- Will they weigh the door, or guess from the old spring? Most companies do not weigh it.
- Is there a trip charge if you decide not to go ahead?
- Is labor covered by the warranty, and for how long?
With us, the consultation is free. You get the price for each option at your door, and you only pay if you go with us.
Can I just buy a spring at Home Depot or Menards?
Rarely in a way that helps. Most big-box stores do not carry torsion springs in the store at all, and the ones that do stock only a couple of sizes, which seldom match what a given door weighs. And a torsion spring is the one part of a garage door we ask homeowners never to install themselves.
Can you open the door with a broken spring?
Please do not try. The spring does the heavy lifting; a typical two-car door weighs well over a hundred pounds, and the spring is what makes it feel light. The opener is built to guide a balanced door, not to lift its full weight. Running the opener against a broken spring can strip the opener's gear or bend the top section of the door.
While you wait for us:
- Do not pull the red emergency release with the door open. With no spring holding it, the door can drop fast.
- Do not try to wind, loosen or remove a torsion spring yourself. The springs hold a lot of stored energy. Our post on whether it is dangerous to replace your own garage door springs explains why.
- If your car is stuck inside, tell us when you call. We plan the day around people who cannot get out.
Signs it is the spring
- A loud bang from the garage, often when nobody was using the door
- A visible gap in the coil of the spring above the door
- The door goes up a few inches and stops, or the opener hums and the door barely moves
- The door feels extremely heavy when you lift it by hand
- The door goes up crooked or the cables hang loose
If that sounds like your door, see what to do when your garage door spring is broken. Curious how long new ones will last? See how long garage door springs last.
Spring replacement across the Chicago area
We replace springs across most of the Chicago area, with the North Shore and northwest suburbs as our home turf. Our technicians carry the common spring sizes on every van and run spring calls every day. Homeowners in Deerfield, where we are based, can often get same-day service. We are on the road daily in Northbrook, Wheeling and Long Grove, and throughout the areas we serve. For everything else on springs, see our garage door spring repair page.
Frequently asked questions
How much does it cost to replace garage door springs in 2026?
Most homeowners pay $450 to $650 to replace a standard pair of garage door springs, parts and labor included. High-cycle springs with longer warranties typically run $650 to $900, and lifetime-type springs $1,000 and up. Very heavy doors that need thicker springs are priced differently.
Is it worth fixing a garage door spring, or should I replace the door?
In almost every case, fix the spring. A broken spring is a wear part, not a sign the door is finished. Replacing the springs (and cables) brings a sound door back to normal. Replacing the door only makes sense if the door itself is damaged, rusted through or very old, and our technician will tell you honestly which it is.
Why do you weigh the garage door before replacing the springs?
Because the spring has to match the door's real weight, and the old spring is often the wrong size. Doors get heavier over the years with insulation, new panels and windows. We put every door on a scale and size the springs to that weight with spring engineering software; we are one of the few companies in Chicagoland that does this. A correctly sized spring balances the door, protects the opener and lasts as long as it is rated to.
Do I pay for the visit if I decide not to go ahead?
No. The in-home consultation is free. Our technician weighs your door, shows you the options and the price for each, and you only pay if you choose to go with us.
Do you replace one spring or both?
On a door with two springs we replace both. They have done the same number of cycles, so when one breaks the other is close to failing.
Which spring should I choose?
It depends on how often your door runs and how long you plan to stay. A low-use door or a planned move fits a standard spring. A busy family door fits a high-cycle spring. If you are staying in the home for good, a lifetime-type spring usually costs the least over time.
How much does it cost to convert extension springs to torsion?
Roughly $900 to $1,300 for most residential doors, including the torsion tube, springs, drums, cables and bearing plates.
Can I use my garage door with a broken spring?
No. The opener is not built to lift the door's full weight, and running it against a broken spring can strip the opener's gear or bend the door. Leave the door closed, do not pull the emergency release with the door open, and call (224) 306-2985.
Get a straight price on your springs
If your door is stuck, or you just want to know which spring fits your house, call AG Smart Garage at (224) 306-2985 or book online. The consultation is free: we weigh the door, show you the options with the reason for each, and you decide. No pressure, no surprises.
